Basic Idea:

• Measure the speed of a projectile; calculate landing position when shot at a specified angle.

• 7 

	What:	How Many:	Where:
	Pasco Projectile Launchers (Choose the launchers specified in Notes below!)	1	non-Majors storeroom, shelf F3
	Projectiles	Place entire box on instructors bench	non-Majors storeroom, shelf F3
	Ram rod	1	non-Majors storeroom, shelf F3
	Catch box	1	non-Majors storeroom, top of shelf R
	Pasco Photogate Timer & power cord	1	non-Majors storeroom, BB3
	Pasco Accessory Photogate (Gate and stereo cable only)	1	non-Majors storeroom, BB4
	Photogate mounting bracket for Pasco Projectile Launcher	1	non-Majors storeroom, shelf F3
	Large bench clamps (see Notes below!)	2	non-Majors storeroom, shelf C4
	Plumb bob	1	non-Majors storeroom, shelf AA3
	30 m measuring tape	1	non-Majors storeroom, shelf AA4
	Metersticks: 1-m and 2-m	1 each	non-Majors storeroom, shelf AA1 & AA2
	Roll of masking tape	1	Jeff will put this out
Shared stuff
	Small table	1	Set up on small table in Bewkes 231; this will be moved into the hallway before the start of lab!
	Carbon paper	Place entire box on instructors bench	non-Majors storeroom, shelf F3
	Small juice cans	Place 3 or 4 on instructors bench	non-Majors storeroom, shelf HH3
	200 g mass	Place 2 in each small juice can	non-Majors storeroom, shelf D3
Stuff Jeff will Get
	Trash cans	1 per setup, if possible	Jeff will get these before lab
	Extension cords	Need 2 6 ft. and 25 ft.	Jeff will get these before lab

Notes:

• Lab Setup (photo details)

• It might be possible to switch rooms with Phys151 if they are doing a curve-fitting exercise. If so, use the setup instructions for Phys151. Ask Jeff which lab will be used 5 launchers will be set up in Bewkes 204: launchers A, C, D, G, H. Launcher (H) will be placed on the movable table from Bewkes 231. Mount launcher (H) on the right-front corner of the small movable table in the 231 lab, and leave the table in that room. Jeff will push this table in the hall before each lab period Photogate notes: Remove the photogate head from the timer support rod by unscrewing the photogate mounting screw from the plastic rod clamp. Put the plastic clamp and the screw in a safe location in the lab. The photogate head and the accessory photogate are attached to the photogate bracket using the mounting screws attached to the bracket (sketch at right) 3 additional launchers (I, L, M) are needed, and will be set up in Bewkes 202; ask Jeff to be sure, in case that room is in use. Set up the three launchers as shown in the second map below. Remove the drawers in the bench under launcher I and L; that makes it easier to attach the clamps!
  Large bench clamp notes: Don't bother clamping launchers to bench; just leave two bench clamps near each launcher. Jeff will align and clamp each one Two large bench clamps are used to secure each launcher to the bench. The large bench clamps have 3 different types of handles, as shown in the photo at right. The best ones to use have a T-handle like 1, where the crossbar can slide back and forth freely. This makes it easy to attach to a tight space on the bench, so these are the preferred ones to use Clamp 2 has a similar handle and can be used for some of the attachments, but there is a large 'knob' at each end of the crossbar, so it's more difficult to attach. Do not use this for the launchers A (on the sink) or I & L (mounted along side bench of Bewkes 202) Clamp 3 has a fixed crossbar that does not move. You have less leverage when trying to make the clamps very tight, so these clamps should not be used for this experiment

• Jeff will get the appropriate number of trash cans before each lab
• Note for Jeff: Print 2 signs for launchers H (in hallway) and C (in 204): Max angle 45 degrees!

Bewkes 204

Bewkes 202 (Lab with Extra Launchers)

• Pasco Projectile Launcher:

  
  Image courtesy of PASCO Scientific

  ---

• Accessory Photogate unit (only the gate is needed!):

  
  Image courtesy of PASCO Scientific

  ---

• Photogate mounting bracket (new!), attached to launcher:

  
  Image courtesy of PASCO Scientific

  ---

• Connecting photogate mounting bracket to Pasco Projectile Launcher:

              

  Images courtesy of PASCO Scientific