- Computers are NOT needed for lab this week
- Jeff will print copies of the conducting paper map for students to use and place on the front bench
- Here is my map with voltage measurements, equipotential lines, and three E vectors, as collected from one of our new apparatus (Spring 2024). The new boards are much more consistent (note the position of the 0-volt line!), symmetrical, and the voltages are higher. We ask students to draw vectors with a 2:1 scale, and some vectors are very large. On my map, I decided to draw the vectors with a 1:1 scale, and they might be a bit short, so I think I'll stick with the 2:1 scale for now.
 Turn on the power supply (one dual-supply, or two singles), located on front bench. Each supply is set for 15.0 volts, and wired so that they provide ±15.0 volts to the conducting sheets through the red and black connectors on the lab bench power panel
- When I remember, I set all the multimeters to the hFE position, so they all start in a neutral setting and have to adjust the knobs immediately
- All of the meters will be connected from their COM port to the green power panel with a long black wire. The red meter probe is connected to the V/Ω port
- Since this is the first time they will use a multimeter, I spend a few minutes going over its basic operation as a voltmeter, and other related topics. A more thorough explanation will take place before next week's Ohm's Law lab:
- Why wires are red & black, and what's a 'banana plug'?
- The purpose of the scale settings
- Tell students to watch for a blinking 'low battery' symbol (extra meters are placed on the instructor's bench, and meters with a low battery should be replaced immediately)
- The power panel is always live; the On/Off switch controls the old timer, not the power!
- Also take a minute to discuss wire handling and safety (pull on the boot, not the wire; never leave wires dangling from a power supply)
- Students first run through an exercise where they learn to use the multimeter as a voltmeter (on the last page of the multimeter instructions)
- Steps f and g of the multimeter exercise ask them about the voltage when measuring across both metal pins. Students generally expect to get 0-volts, so it's worth explaining why they get ±30-volts. You can demonstrate with their meter probes on the sketch in their directions, or with a black and red wire using the topographic map I draw on the board:
 |
 |
 |
| +15 volts, with respect to zero-potential surface |
+30 volts, with respect to the negative metal pin |
-30 volts, with respect to the positive metal pin |
- Students are provided with a copy of the 'map' along with their instructions. Each person does their own map, which they bitch about, but it's important. Frequently, one partner will draw the E vectors incorrectly, so it's an important exercise for them
- Lazy students may wish to have one write the voltages on the map, then photocopy the map. That's fine, as long as they both then plot the potential field lines and E vectors
- Student's who don't follow the directions carefully may unplug the conducting paper board from the power supply. Make sure the wire from the right-pin is plugged into the red (+15 volts) connector, the left-pin into the black (-15 volts) connector on the power panel between the benches
 (New, Spring 2019) Students will mark the 0-v equipotential line by dragging the meter probe along the conducting paper. Using this procedure for the other equipotential lines is tedious and produces lousy results due to the inconsistency of the conducting boards. Since we already have them measure the voltage at each marked point, they will use interpolation to determine the position of the ±2, ±4 and ±6-volt lines. I've added a picture (at right) and instructions – and didn't use the word 'interpolation' – so we'll see how that goes.- Students get worried when their map doesn't look like the 'ideal'; this was a problem with the old boards, but the new ones are pretty good. Make sure connections are tight, the needle-probe is screwed in tight, and that they're measuring correctly (don't wiggle the probe!)
- Jeff has a spreadsheet for checking the value of the electric field components, Ex and Ey, from their voltage measurements. Be nice to him, and he'll treat you well
- Common mistakes:
- Dropping a sign when calculating Ex and Ey so that they point in the opposite direction
- Correctly calculating Ex and Ey but then graphically adding them incorrectly on the field map
- In the multimeter exploration section, thinking that the out-of-range warning is an actual measurement (they include units of volts)
- Students will write that the system "stimulates" a pair of charges. Hilarious.
|
